Single or Dual Path Light Commercial Fire Communicator (AT&T)
Last updated Nov 1, 2026 · 2 entries in Page history
The Honeywell HWF2A-COM is a single or dual path light commercial fire communicator that sends Contact ID reports from any fire alarm control panel with a built-in dialer over LTE on AT&T, over IP, or both.
As the source prints itPower SupplyPrimary: 120VAC, 60Hz, 0.5A, Secondary: 18VDC, 50VAPress to see it in the sheet ↓
As the source prints itProduct Height14.88 in, 37.8 cmPress to see it in the sheet ↓
As the source prints itProduct Width12.75 in, 32.4 cmPress to see it in the sheet ↓
As the source prints itProduct OverviewThe HWF2-COM Series LTE/IP fire communicators have three selectable reporting paths including LTE cellular only, IP only, or IP primary with LTE cellular backup. All signals from the HWF2-COM Series are delivered to the AlarmNet® network control center which routes highly encrypted, cybersecured data packets via a customer-provided Internet connection or LTE cellular network to the appropriate central station.
LTE and IP connection tested every day
Requires no change to the existing FACP configuration
Plan choices range from 5 minute, 60 minute, 6 hour, and 24 hour supervision intervals
Data transmits over standard Contact ID protocol but is secured with the industry’s advanced encryption standard (AES 256 bit)
Supports both dynamic (DHCP) or public and private Static IP addressing
Reliable connection: IP and cellular connection tested every day
Built-in, standalone power supply module. Onboard charging circuit design accommodates battery backup. Includes primary power and battery supervision
Diagnostic LEDs indicate signal strength and status
7720P Handheld programmer for easy setupPress to see it in the sheet ↓
- Part number or model
- HWF2A-COM
- Catalog number
- Not assigned yet
No confirmed photo of this model
Specifications
27 fields, as the sources state them
Overview
- Overview
- The HWF2-COM Series LTE/IP fire communicators are single or dual path light commercial fire alarm communicators that offer Contact ID reporting with any FACP (fire alarm control panel) with a built-in dialer.1
Specifications
- For Use With
- CELL-ANT3DB: 3dBA gain antenna, WA7626-CA: SMA to N adapter cable, 7626-50HC: 50 ft. antenna cable, low loss1
- Application
- Single or dual path commercial fire alarm communicators1
- Approvals and Standards
- UL Listed: S789, CSFM: 7300-1645:0511, FDNY: Approved1
- Includes
- Red cabinet with key and lock, Wall outlet box, Dialer capture module, LTE communications module, Antenna and mounting adapter, LED display board, Transformer, PowerBoost1 power supply1
- Power Supply
- Primary: 120VAC, 60Hz, 0.5A, Secondary: 18VDC, 50VA1
- Product Height
- 14.88 in, 37.8 cm1
- Product Width
- 12.75 in, 32.4 cm1
- Product Weight
- 5.3 lb, 6.94 kg1
- Product Depth
- 9.25 in, 23.9 cm1
- Color
- Red1
- Ambient Relative Humidity (Max)
- 93 % RH +/- 2%1
- Ambient Operating Temperature (Max)
- 120 °F, 49 °C1
- Ambient Operating Temperature (Min)
- 32 °F, 0 °C1
- Carrier
- AT&T1
- Indoor or Outdoor Use
- Indoor1
Product Overview
- Product Overview
- The HWF2-COM Series LTE/IP fire communicators have three selectable reporting paths including LTE cellular only, IP only, or IP primary with LTE cellular backup. All signals from the HWF2-COM Series are delivered to the AlarmNet® network control center which routes highly encrypted, cybersecured data packets via a customer-provided Internet connection or LTE cellular network to the appropriate central station. LTE and IP connection tested every day Requires no change to the existing FACP configuration Plan choices range from 5 minute, 60 minute, 6 hour, and 24 hour supervision intervals Data transmits over standard Contact ID protocol but is secured with the industry’s advanced encryption standard (AES 256 bit) Supports both dynamic (DHCP) or public and private Static IP addressing Reliable connection: IP and cellular connection tested every day Built-in, standalone power supply module. Onboard charging circuit design accommodates battery backup. Includes primary power and battery supervision Diagnostic LEDs indicate signal strength and status 7720P Handheld programmer for easy setup1
Electrical
Cabinet Specifications
- Cabinet Specifications: Dimensions
- 14.875" H x 12.75" W x 3.0" D (37.8cm H x 32.4cm W x 7.6cm D)2
Shipping Dimensions
Temperature and Humidity Ranges
- Temperature and Humidity Ranges
- This system meets NFPA requirements for operation at 0-49° C/32-120° F and at a relative humidity 93% +- 2% RH (noncondensing at 32° C +- 2° C (90° F +-3° F). However the useful life of the system’s standby batteries and the electronic components may be adversely affected by extreme temperature ranges and humidity. Therefore, it is recommended that this system and its peripherals be installed in an environment with a normal room temperature of 15-27° C/60-80° F.2
Installation Requirements, UL Compliance
- Installation Requirements, UL Compliance
- To meet UL864/NFPA requirements, ensure the following: HWF2-COM Series must be installed in accordance with the National Fire Protection Association (NFPA) standards 70 and 72. HWF2-COM Series must be mounted in the same room and within 20 feet of the fire panel. HWF2-COM Series and all equipment used for the IP connection (e.g., router, hub, modem, etc) must be UL-listed, powered from an unswitched branch circuit, and be provided with appropriate standby power. HWF2-COM Series must use the 7AH battery (not included) to provide 24 hour backup capability. The Telco line wiring and the Power Transformer wiring must be routed through conduit.2
Product Line Information
- Both models include
- Red cabinet with key and lock Wall outlet box Dialer capture module LTE communications module Antenna and mounting adapter PowerBoost1 power supply LED display board Transformer Manual and required screws Cables, etc.2
Sources: resideo.com, Product page, read Nov 1, 2026 UTC; resideo.com, HWF2-COM Series data sheet PDF, pages 2 and 3, read Nov 1, 2026 UTC.
Size and weight
Inches and pounds, millimetres and kilograms
The product
| What | Inches and pounds | Millimetres and kilograms |
|---|---|---|
| DimensionsCabinet | H14.875 | H37.8 |
The packaging
| What | Inches and pounds | Millimetres and kilograms |
|---|---|---|
| DimensionsShipping | H15.625 | H39.7 |
| WeightShipping, the maker's two figures do not convert | 5.3 lb | 6.94 kg |
Figures in black are the maker’s. Figures in grey are converted by the wiki (1 in = 25.4 mm, 1 lb = 0.45359237 kg).
Compare with
1 of the same family on the wiki
More from Honeywell
4 pages on the wiki
Documents
1 linked, none copied here
References
2 sources, each with the day it was read
- resideo.com, Product page, read Nov 1, 2026 UTC. Supports 17 specifications, the related products
- resideo.com, HWF2-COM Series data sheet PDF, pages 2 and 3, read Nov 1, 2026 UTC. Supports 10 specifications, the related products, the documents
Page history
Every read and every change to this page, newest first
- Page created from the maker’s page, among the products buyers searched on PriceQ. Product type proposed. Descriptions written at three lengths from the specifications.Claude Opus (AI agent) · Not reviewed yet
- Read on resideo.com: Product page; HWF2-COM Series data sheet PDF, pages 2 and 3.Claude Opus (AI agent) · Not reviewed yet
The descriptions are written by the wiki from the specifications above, never copied from the maker.
Live prices · PriceQ
What sellers ask for the Honeywell HWF2A-COM today.
The wiki holds what the maker publishes. PriceQ looks up the sellers. The button opens it with this product already filled in.